Commercial ventilation, Somerset
Ductwork installation in Somerset
Spiral and rectangular galvanised ductwork, hung, insulated and sealed, across Somerset.
- From £45 + VAT per metre
- Free survey
Ductwork carries air between the fan or unit and the rooms it serves, and how it is sized, hung and sealed decides how well the whole system performs. We supply and install spiral and rectangular galvanised ductwork, fittings, dampers, insulation and access panels.
Every job in Somerset gets a written quote before it starts and a commissioning record when it finishes. We cover Bridgwater, Portishead, Frome, Burnham-on-Sea and Bath and the villages around them.
Ductwork in Somerset at a glance
- Area
- Somerset
- Towns listed
- 19, largest Bath
- Postcode districts
- BA4, BA5, BS21, BS48, BA1 and BA2
- Price region
- South West
- Survey
- Free survey (UK mainland)
How we do it
Undersized or leaky ductwork forces fans to work harder and makes systems noisy. We work to recognised sheet-metal ductwork specifications, seal joints, fit access panels for cleaning and insulate ducts that run through cold spaces or carry cold air. We install for our own ventilation systems and for other contractors, from short runs in a shop to full warehouse and office distribution.
Access panels
Fitted for future cleaning and inspection.
Spiral ductwork
Round galvanised ductwork for supply and extract runs.
Rectangular ductwork
For larger volumes or limited ceiling depth.
Guide prices in Somerset
| Work | Guide price |
|---|---|
| Spiral ductwork supplied and installed (up to 315 mm diameter) (per metre) | £45–£100 + VAT |
| Rectangular ductwork supplied and installed, insulated where needed (per metre) | £100–£235 + VAT |
South West rates shown. Prices exclude VAT. The fixed price is confirmed in writing after we have seen the job.
When to get it looked at
- No access panels for cleaning
- Uninsulated ducts dripping condensation
- A new system needs distribution ductwork
Rules in England
In England, ventilation is covered by Part F of the Building Regulations and its guidance, Approved Document F (2021 edition). Workplaces must also be ventilated with a sufficient quantity of fresh or purified air under the Workplace (Health, Safety and Welfare) Regulations 1992.
How the job runs
- Survey
- Drawings
- Install
- Insulate
- Test
Towns we cover in Somerset
- Bath
- Weston-super-Mare
- Taunton
- Yeovil
- Bridgwater
- Portishead
- Frome
- Burnham-on-Sea
- Clevedon
- Nailsea
- Keynsham
- Chard
- Midsomer Norton
- Street
- Minehead
- Bishopsworth
- Wells
- Shepton Mallet
- Yatton
Questions about ductwork installation in Somerset
Is the survey free in Somerset?
For new installations on the UK mainland, yes. The survey is free and the quote that follows is fixed and in writing. Servicing, testing and repair visits are charged, and we confirm the cost before booking.
Do ducts need insulation?
Ducts carrying cold or warm air through unheated spaces usually need insulation to prevent heat loss and condensation.
Do you fit fire dampers?
We fit fire dampers where the design requires them; their selection and testing follow the fire strategy for the building.
Which rules apply to ventilation in Somerset?
In England, ventilation in new and altered homes is covered by Approved Document F of the Building Regulations. Landlords also have duties under the Housing Health and Safety Rating System, and workplaces must be ventilated under the Workplace (Health, Safety and Welfare) Regulations 1992.
Which towns in Somerset do you cover?
All of Somerset, including Bridgwater, Portishead, Frome, Burnham-on-Sea and Bath. If your town is not listed, send the postcode and we will confirm.
Other services in Somerset
Get a guide price in two minutes
Answer a few questions for a price range, or send photos and we will come back to you with a written quote.